If your well pump is running all the time and never shuts off, you are paying for water your home is not using. A pump that hums steadily from the well house or basement around the clock is drawing continuous electricity, wearing its motor far faster than it was designed for, and in the large majority of cases there is a specific, fixable reason: a hidden leak, a failed check valve, a stuck pressure switch, or a pump that simply cannot reach the pressure that is supposed to stop it. In more than 20 years of inspecting residential wells across the western US, this is one of the two most common pump complaints we see (the other being short cycling), and the cause is almost always findable in under an hour with a $15 pressure gauge. In this 2026 guide we break down the nine causes that account for nearly every case, a 30-minute field test you can run yourself, the fixes ranked by cost, and the parts worth keeping on the shelf so the next one is a twenty-minute repair instead of an emergency call.
Disclosure: As an Amazon Associate, we earn from qualifying purchases on this page. Product selections are based on independent research and real well water data.
By Robert Harrison, Certified Well Inspector
Robert has 20+ years of experience inspecting and testing residential and agricultural water wells across the western US. He has evaluated well water quality and pump systems for hundreds of homes, farms, and ranches.
Published: November 2026
Table of Contents

Why a Well Pump Running All the Time Is a Problem
A healthy residential system runs the pump for two to five minutes when a fixture opens, then lets it rest for the rest of the hour. When the pump runs all the time, three things happen at once. First, the bill climbs: a 1/2- to 3/4-HP submersible or jet pump draws roughly 0.8 to 1.2 kilowatts while running, so 24 hours a day means 600 to 900 kWh per month, or $60 to $140 in electricity versus the $15 to $30 a normally cycling system uses. Second, the motor wears out: well pumps are rated for intermittent duty, and continuous operation cooks the windings, dries out the bearings, and shortens a 20-to-30-year pump life down to months. Third, the nonstop running is itself a symptom — the system is trying to reach a cut-out pressure it can no longer reach, which is the same root condition behind low water pressure and pump failure. According to USGS groundwater guidance, a well's yield (how fast the aquifer refills the well) is the ceiling on how much water a pump can sustainably move, and most "pump running all the time" problems trace back to either demand exceeding that yield or pressure being lost before it reaches the tank.
The numbers that matter
A 1/2-HP submersible running nonstop uses 600–900 kWh per month. Typical monthly electricity for a healthy well system: $15–30. Typical continuous-running system: $60–140 or more. Every month of nonstop running is roughly $30–80 of pure waste on top of the accelerated motor wear.
| Metric | Healthy System | Pump Running All the Time |
|---|---|---|
| Run time | 2–5 min per cycle, a few cycles per hour | Continuous, 24 hours a day |
| Gauge behavior | Builds to 40–50 PSI and holds | Stalls below cut-out, or holds pressure but pump never stops |
| Monthly electricity | $15–30 | $60–140+ |
| Expected motor life | 20–30 years typical | Months to a few years of continuous duty |
The 9 Causes of a Well Pump Running All the Time
We rank these by how often we actually find them in the field, which is not the same order as how often you will read about them online. The first four causes account for roughly 80% of the cases we diagnose.
1. A Hidden Leak in the House Plumbing
The single most common cause of a well pump running continuously is a slow leak on the house side of the system. The classic culprit is a worn toilet flapper or fill valve — a single running toilet can waste 200 gallons or more per day, enough to keep a 1/2-HP pump cycling nonstop. Other house-side leaks include a leaking hose bibb, a cracked pipe in a wall, a failed tank-to-house connection, or a slow drip at a fixture gasket. The giveaway is that the pump runs even at 3 a.m. when nothing is running. Dye the toilet tanks, check every outdoor spigot, and listen at the tank gauge over an hour with every fixture closed.
2. A Leak in the Irrigation or Exterior System
In the summer months the most common exterior cause is a stuck-open irrigation solenoid valve or a burst lateral line running under the lawn. A cracked sprinkler main can dump 30 to 50 gallons per minute straight into the ground, and a submersible pump will happily run 24 hours a day trying to keep up. Shut the irrigation master off at the riser and watch the gauge: if the pump finally shuts off, you have found your leak. The same test isolates a continuously weeping outdoor spigot or a failed backflow preventer on the lawn side.
3. A Worn or Stuck Check Valve
The check valve in the well (a foot valve at the bottom of the jet-pump riser, or a swing check at the submersible discharge) is the only thing stopping the column of water from draining back down the well when the pump stops. When it wears, sticks open, or loses its seal, every gallon the pump pushes partly drains back underground, and the pump runs continuously to chase a pressure it can never quite build. In our experience this is the most common cause when the pump runs all the time but the pressure gauge still looks almost normal. The fix is to replace the check valve or foot valve for your well pump, which on a shallow jet system is a $20 to $60 part.
4. A Pressure Switch Stuck On
The pressure switch is the tiny device on the tank that tells the pump to stop. If its contacts weld together from arcing, or its diaphragm ruptures, the switch keeps power to the motor no matter what the pressure does. The signature here is unusual: the gauge reads a normal 40 to 50 PSI, the pressure holds, and yet the pump keeps running. That combination almost always means the electrical side, not the plumbing. A related variant is a flow switch or pump controller stuck in the on position, which behaves the same way. The fix is a new well pump pressure switch ($25 to $80) and, if the contacts were pitted badly, a new contactor to match.
5. An Undersized Pump for the Well
Every pump has a maximum head — the highest pressure it can reach at zero flow. If your well is deep, the pump is old, or the original pump was simply undersized, it may be physically incapable of reaching the 40 or 50 PSI cut-out that the switch is waiting for. The pump then runs at or near its shutoff curve forever. If your well was drilled or deepened recently, or if neighbors report dropping water levels, an undersized or out-matched pump is a real possibility rather than a leak. This is the most expensive cause on this list: the fix is a properly sized pump, selected against your well's actual depth and flow, which is why the field test in the next section comes first.
6. A Dropped Water Level or Clogged Screen
Wells are not static. Drought, heavy nearby pumping, or a clogged or sand-loaded well screen can drop the static or pumping water level well below where the pump was installed. The pump then draws less flow, cannot build cut-out pressure, and runs continuously while slowly losing performance. According to EPA private well guidance, pumping water level is the number that determines how hard your system works. A clogged screen shows the same symptom from the other direction: the pump is fine, the well is fine, and the screen simply will not let enough water in. A pump pulling low amperage while running flat is the classic fingerprint of this cause — see our well pump amp draw guide for how to read the numbers.
7. A Clogged Discharge Line or Filter
Less common but real: scale, sand, or debris can partially block the discharge line between the well and the tank, or clog an inline filter. The pump pushes against the restriction, reaches less pressure at the tank than it is actually making, and never triggers the cut-off. If the pump is strong at the breaker test but weak at the gauge, look for the restriction. A badly clogged sand filter on a submersible system will do exactly this, and clearing or replacing the filter stops the continuous running immediately.
8. A Cut-Out Set Above What the Pump Can Reach
The pressure switch is adjustable, and a previous owner or contractor may have set the cut-out higher than the pump can actually produce. On a system that used to be right at the edge, a few years of mineral buildup or a slightly lower water level tips it over the line, and the pump chases a 55 PSI it has never once reached. The fix is to reset the switch to the standard 30/50 spread (or whatever matches your pump curve) and recheck — our pressure tank precharge guide covers the correct air charge and switch settings together, because the two must be consistent for the tank to work.
9. A Failing Motor or Worn Impeller
Finally, the pump itself can be dying. Worn impeller vanes, a corroded shaft, or a motor with failing bearings loses head over time until it can no longer reach cut-out. The pump runs continuously and the water feels weaker than it used to. This is the last cause to confirm because the fix is the most expensive: a new pump. If you are seeing other symptoms at the same time — humming that never builds, a burning smell, or the breaker tripping — check our guide on the signs of a failing well pump before deciding whether repair makes sense.
How to Diagnose It: A 30-Minute Field Test
You do not need a well driller to narrow this down. All you need is the tank gauge, a helper with a phone timer, and optionally a $15 pressure gauge and a clamp meter. Run the tests in this order, because each one rules out a whole branch of causes.
- Read the gauge while the pump runs. Open one outdoor faucet fully and watch the tank gauge. If pressure builds to 40–50 PSI and holds, but the pump keeps running, the problem is electrical — cause #4, a switch or controller stuck on. If pressure stalls somewhere below cut-out, the problem is hydraulic — one of causes 1, 2, 3, 5, 6, 7, or 8.
- Run the static hold test. Turn the pump off at the breaker, close every faucet, and record the gauge reading. Wait 30 minutes. A drop of 5 PSI or more means water is leaving the system — a leak (cause 1 or 2), a failed check valve (cause 3), or a weeping tank air charge. A drop under 2 PSI means the system holds pressure fine, which points at the switch or the pump itself.
- Isolate house from well. Shut the main supply valve between the tank and the house. If the gauge now holds steady, the leak is in the house: dye every toilet tank, then check outdoor spigots and the irrigation master. If it still bleeds down with the house closed, the loss is at the well — check valve, riser, or the well itself.
- Check the tank air. With the pump off and a tap run briefly to drop the water-side pressure, unscrew the air cap and read the charge with a tire gauge. It should sit about 2 PSI below the switch cut-in. If you get 0 PSI or water spits out, the tank is waterlogged — not the primary cause of continuous running, but it will make everything else worse and it means the bladder is failing.
- Open the pressure switch. With power off, remove the switch cover and look at the contacts. Pitting, black arcing marks, or contacts that do not spring back mean the switch is the problem. Also note the cut-in/cut-out setting and compare it to what the pump is rated to reach.
- Test for backflow into the well. With the pump off and the house valve closed, open one outdoor tap and watch the gauge fall. If pressure bleeds off fast even with no visible leak, the check valve at the well is likely passing, and the pump is chasing its own backflow.
- Check the amp draw. Clip a meter around one wire at the contactor while the pump runs. A 1/2-HP submersible should draw roughly 5–8 amps; a 3/4-HP unit roughly 8–12. A pump drawing far below normal while running flat is starving for water — low level or clogged screen (cause 6). Normal amps with low pressure means the water is going somewhere: a leak downstream (cause 1, 2, or 7).
Safety note
The pump, switch, and contactor run on 120V or 240V. Always kill the breaker before opening the switch cover or contactor, and test the wires with a meter before trusting the breaker. If the well house is wet or the wiring looks corroded, stop and call a licensed electrician or well contractor.
The Fixes, Ranked by Cost
Most of these are parts-and-an-hour jobs. Work down the list until the pump shuts off and holds pressure.
- Replace the toilet flapper or fill valve — $5 to $15. The cheapest fix on the list and the most common. A single running toilet can keep a whole pump busy all day.
- Find and repair the exterior leak — $20 to $200. Stuck irrigation solenoid, cracked lateral, or weeping spigot. Shut the irrigation master during the test to isolate it fast.
- Replace the check valve or foot valve — $20 to $60 for the part. On a submersible system the swing check at the discharge is often accessible from the well house; on a deep well it is a pump-pull job.
- Replace the pressure switch — $25 to $80. Match the standard 30/50 spread and the amp rating to your pump. If the contacts were badly welded, replace the contactor at the same time ($20 to $40).
- Reset the switch and tank air to a consistent setting — free, with a tire gauge. Cut-out at 50, tank air at 28, spread and precharge consistent. If your system is cycling hard rather than running flat, see our well pump short cycling guide for the full precharge procedure.
- Clear or replace a clogged filter or line section — $30 to $150. Sand filters and inline strainers are the usual offenders.
- Replace a waterlogged pressure tank — $150 to $400. Not the root cause of continuous running, but a dead bladder forces short cycles and hammer that compound the problem. A 44-gallon bladder tank is the standard residential replacement.
- Redevelop the well or clean the screen — $500 to $2,500. Air-lifting, jetting, or swabbing to restore flow when the water level or the screen is the limit.
- Replace the pump with a correctly sized unit — $1,500 to $5,000 installed. The last resort, and the right one only when the well's actual depth and yield prove the old pump was out of its range. Pair it with a two-speed switch if you are seeing hard cycling: see our two-speed pressure switch guide.
Which Cause Is Yours? Comparison Table
| Cause | What you will see | First test | Typical fix cost |
|---|---|---|---|
| House leak | Pump runs at night, gauge stalls low, static test drops fast | Dye the toilets, 30-min static hold | $5–200 |
| Irrigation / exterior leak | Worse in summer, pump runs with all faucets closed | Shut irrigation master, watch gauge | $20–200 |
| Failed check valve | Gauge nearly normal, pressure bleeds with house closed | Backflow test with house valve shut | $20–60 |
| Switch stuck on | Gauge normal and holding, pump still runs | Open switch cover, check contacts | $25–80 |
| Low water level / clogged screen | Low amp draw, weak flow, got worse after a dry spell | Clamp meter on the contactor | $500–2,500 |
| Undersized / failing pump | Normal amps, never reached cut-out in the last months | Compare pump curve to well depth | $1,500–5,000 |
Parts Worth Having: Best Products to Stop It
These are the parts that resolve the vast majority of continuous-running calls. Buy the switch and tank before you need them — a pump running flat at 2 a.m. is not a good time to discover the hardware store closed at 6.
- Well Pump Pressure Switch 30/50 PSI — the standard replacement switch for residential systems. Get the 15- or 20-amp version to match your pump rating.
- 44-Gallon Bladder Pressure Tank — the standard residential size, for replacing a waterlogged tank that is forcing hard cycling on top of the main problem.
- 30-Amp Pump Contactor — replace it whenever the old one has welded or pitted contacts; it is the second switch in the chain and it fails silently.
- Well Pump Foot Valve with Check — the fix for a jet system that will not hold pressure because the column drains back into the well.
- 0–100 PSI Pressure Gauge — the $15 tool that runs the entire 30-minute field test in this guide.
- Pump Start Capacitor — for capacitor-start jet pumps that hum but struggle to build pressure; match the MFD rating to the old unit.
- Well Pump Flow Switch — the replacement part when a stuck flow switch is holding the pump on.
| Part | Typical price | What to look for |
|---|---|---|
| Pressure switch 30/50 | $25–80 | 15–20 amp rating, 1/2" NPT, standard 30/50 spread |
| 44-gal bladder tank | $150–400 | Replaceable bladder, 150 PSI rating, 1" connection |
| 30-amp contactor | $20–40 | Match voltage (120/240) and coil rating to the old unit |
| Foot valve | $20–60 | Match riser size (1" or 1-1/4"), brass or cast iron |
| 0–100 PSI gauge | $10–25 | Brass 1/4" NPT, glycerin-filled for vibration |
| Start capacitor | $15–40 | Same MFD and voltage rating as the existing unit |
| Flow switch | $25–60 | Match pipe size and switch current rating |
Prices reflect typical 2026 retail ranges for residential 1/2- to 3/4-HP systems. Verify your pump's nameplate voltage and amp rating before ordering electrical components.
When to Call a Professional
Call a well contractor or licensed electrician rather than DIYing when any of these is true. The well is deep (over about 150 feet) and the check valve or pump itself needs pulling, the amp test shows the pump is running dry or drawing far below normal — keep the pump off until it is diagnosed, because a starving pump destroys itself in hours. The static hold test drops 10 PSI or more with everything closed, which points at a leak at the well collar or a cracked riser that is not visible from the house side. The water level has clearly dropped after a dry season and the well needs redevelopment or a deeper pump setting. Or the switch, contactor, or wiring shows burn marks and corrosion — 240V work in a damp well house is not a first DIY project. A well contractor can also pull the pump, check the screen, and log the true pumping water level in one visit, which is the data you need before buying a replacement pump. If the symptoms include a humming motor that never builds, a burning smell, or a tripping breaker, stop using the well and see our signs of a failing well pump while you arrange service.
See Also: Related Well System Guides
Frequently Asked Questions
How long is too long for a well pump to run?
Two to five minutes per cycle is normal for a residential system. If the pump runs more than 10 to 15 minutes without shutting off, or never shuts off at all, the system cannot reach its cut-out pressure and one of the nine causes on this list is at work. Run the 30-minute field test to find out which one.
Can a well pump run 24/7 without breaking?
Not for long. Residential well pumps are rated for intermittent duty — a few minutes of running followed by long rest periods. Continuous operation keeps the motor near its thermal limit, dries out the bearings, and on submersibles can overheat the pump in the well where it cannot be seen. A pump that has run nonstop for weeks or months should be treated as at-risk even if it still appears to be working.
Why does my well pump run all the time but the pressure looks normal?
That combination points at the electrical side: a pressure switch with welded contacts, or a flow switch or controller stuck in the on position. The system is actually reaching cut-out pressure, but the signal to stop never arrives. Open the switch cover (power off first) and inspect the contacts. This is also the case where replacing the switch and contactor fixes the problem in an afternoon.
How do I know if my pump is too small for my well?
Compare the pump's maximum head at zero flow (on its curve chart or nameplate) against your cut-out pressure plus the depth to the water level. If the pump's max head is only slightly above your cut-out, any drop in water level or flow pushes it over the edge and it runs forever. A practical field check: run the pump with a single outdoor tap open at full and time how long it takes the gauge to stall. A pump that stalls near zero flow is out of its range for this well, and the fix is a correctly sized replacement selected against the well's actual depth and yield.
Does a well pump running all the time waste a lot of electricity?
Yes — it is one of the largest single electricity wastes in a well home. A 1/2- to 3/4-HP pump running continuously uses 600 to 900 kWh per month, roughly $60 to $140 at typical 2026 residential rates, compared with $15 to $30 for a system that cycles normally. The fix is usually a part costing under $100, so the payback on finding the real cause is measured in days, not months.
#WellPump #WellWater #WaterPressure #PressureTank #PumpRepair #WellMaintenance #HomeownerTips #WellSystem #SubmersiblePump #JetPump #WaterWell #DIYRepair #WellOwner #WellDrilling #WaterWellOwners
